[GH-ISSUE #337] [Feature]: In the printers dashboard - add in a feature to click the printer and manually adjust the bed temp #216

New issue

Closed

opened 2026-05-07 00:07:45 +02:00 by BreizhHardware · 3 comments

BreizhHardware commented

2026-05-07 00:07:45 +02:00

Owner

Originally created by @TechnoPrints on GitHub (Feb 11, 2026).
Original GitHub issue: https://github.com/maziggy/bambuddy/issues/337

Originally assigned to: @maziggy on GitHub.

Problem or Use Case

One of my issues with the H2S is that it consumes so much power on startup. I usually have to manually adjust it by 5C in order to not make my UPS beep.

Proposed Solution

Add a feature where i can control the temps in printers but also adding in a feature the slowing increments the temperature so it doesn't blow my fuse.

Alternatives Considered

No response

Feature Category

Print Archiving

Priority

Nice to have

Mockups or Examples

No response

Contribution

I would be willing to help implement this feature

Checklist

I have searched existing issues to ensure this feature hasn't already been requested

Originally created by @TechnoPrints on GitHub (Feb 11, 2026). Original GitHub issue: https://github.com/maziggy/bambuddy/issues/337 Originally assigned to: @maziggy on GitHub. ### Problem or Use Case One of my issues with the H2S is that it consumes so much power on startup. I usually have to manually adjust it by 5C in order to not make my UPS beep. ### Proposed Solution Add a feature where i can control the temps in printers but also adding in a feature the slowing increments the temperature so it doesn't blow my fuse. ### Alternatives Considered _No response_ ### Feature Category Print Archiving ### Priority Nice to have ### Mockups or Examples _No response_ ### Contribution - [ ] I would be willing to help implement this feature ### Checklist - [x] I have searched existing issues to ensure this feature hasn't already been requested

BreizhHardware

2026-05-07 00:07:45 +02:00

closed this issue
added the
wontfix
label

BreizhHardware commented

2026-05-07 00:07:46 +02:00

Author

Owner

@TechnoPrints commented on GitHub (Feb 11, 2026):

same would go for left and right nozzles, i would like to set temps on the main screen

@TechnoPrints commented on GitHub (Feb 11, 2026): same would go for left and right nozzles, i would like to set temps on the main screen

BreizhHardware commented

2026-05-07 00:07:46 +02:00

Author

Owner

@maziggy commented on GitHub (Feb 12, 2026):

Unfortunately this is outside the scope of what Bambuddy can reasonably solve — the power draw at startup is a hardware/electrical issue that's better addressed at the infrastructure level (e.g. a higher-rated UPS or a smart plug with soft-start). Bambu Lab printers don't expose granular heater ramping controls over MQTT, so there's no reliable way to implement gradual temperature stepping from software.

@maziggy commented on GitHub (Feb 12, 2026): Unfortunately this is outside the scope of what Bambuddy can reasonably solve — the power draw at startup is a hardware/electrical issue that's better addressed at the infrastructure level (e.g. a higher-rated UPS or a smart plug with soft-start). Bambu Lab printers don't expose granular heater ramping controls over MQTT, so there's no reliable way to implement gradual temperature stepping from software.

BreizhHardware commented

2026-05-07 00:07:46 +02:00

Author

Owner

@TechnoPrints commented on GitHub (Feb 12, 2026):

There wouldn't be a way to set bed temps or nozzle temps through the dashboard? Also it wouldn't be possible to add in a soft start that would incrementally add 3C per 5 seconds? I don't think it needs to be too complicated

@TechnoPrints commented on GitHub (Feb 12, 2026): There wouldn't be a way to set bed temps or nozzle temps through the dashboard? Also it wouldn't be possible to add in a soft start that would incrementally add 3C per 5 seconds? I don't think it needs to be too complicated

BreizhHardware referenced this issue

2026-05-07 00:15:14 +02:00

[PR #225] [MERGED] v0.1.6.2 #967